LTFS for Windows not working, "The Parameter is Incorrect" in Explorer (1334 Views)
Reply
Occasional Collector
bdlitsupport
Posts: 1
Registered: ‎08-05-2012
Message 1 of 6 (1,334 Views)

LTFS for Windows not working, "The Parameter is Incorrect" in Explorer

I thought I'd try the new LTFS for Windows (Standalone on Win 7 x64)  July 2012,  version 1.2.2 I think.

With HP 3000 Drive on HP LSI based SAS card.

 

It installed ok.

The media can be formatted ok. (Obviously detecting the tape drive and partitioning the media ok)

 

When I  R-Click on the drive in explorer, expecting to be able to "Mount", There is no LTFS specific options.

If I L-Click, it returns "The parameter is Incorrect"

 

The "FUSE4Win File System Launcher" Service is installed.

 

 

Tests with ltt show the drive is working perfectly.

Firmware is  Z5AD

SN:   HU1201LCTJ

 

Windows is 7, Sp1, fully patched on HP Z200.

 

There are no errors in the even log other the "LTFS" can't open tape0, --which happens when I start the PC without a tape in the drive.

 

Any help welcome..

--John

 

Occasional Visitor
mutic_predrag
Posts: 1
Registered: ‎08-27-2012
Message 2 of 6 (1,217 Views)

Re: LTFS for Windows not working, "The Parameter is Incorrect" in Explorer

I have exactly the same problem. Does anybody have solution to this?

Occasional Visitor
KiwiiDigital
Posts: 1
Registered: ‎02-28-2013
Message 3 of 6 (1,052 Views)

Re: LTFS for Windows not working, "The Parameter is Incorrect" in Explorer

I got the same issue, someone can help us?
Trusted Contributor
Rajanikant
Posts: 202
Registered: ‎10-12-2006
Message 4 of 6 (1,033 Views)

Re: LTFS for Windows not working, "The Parameter is Incorrect" in Explorer

Hi,

 

From what i understand there must be a configuration issue for this problem. just to start with you can refer to the chapter 3 in the guide available http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c03431222/c03431222.pdf

 

and confirm the steps you are following are correct.

 

If that didn't help you can probobly collect the contents of "\ProgramData\Hewlett-Packard\LTFS\" and attatch them here so we can try to help

Regards

Raj

How to assign points? Click the KUDOS! star!
Occasional Visitor
eurocapa
Posts: 1
Registered: ‎04-04-2013
Message 5 of 6 (996 Views)

Re: LTFS for Windows not working, "The Parameter is Incorrect" in Explorer

Hi,

 

Same issue here, Mapping ok, LTFS FORMAT ok but when i r-clik on the LTFS icon in windows explorer, I don'thave LTFS properties and when I clik on it, the parameter is incorrect. Also, my drive is not seen as RAMDISK but like local disk.

 

I am using LTFS 2.0 and running WIndows 7 x64.

If anyone can help please !

 

thank you,

regards

Occasional Visitor
James Rodgers
Posts: 2
Registered: ‎03-19-2008
Message 6 of 6 (968 Views)

Re: LTFS for Windows not working, "The Parameter is Incorrect" in Explorer

Hi,

 

LSI HBAs are not a supported SAS card for LTFS with HP Utrium drives.  a P212 Array controller or higher with at least 256MB cache is the supported option.

This may not be your immediate issue, but uit certainly will stop you writing to the tape.

 

regards

 

Roland

The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation.