How to change RAID level in production server (Hardware RAID) (1683 Views)
Reply
Super Advisor
senthil_kumar_1
Posts: 901
Registered: ‎03-02-2009
Message 1 of 2 (1,683 Views)

How to change RAID level in production server (Hardware RAID)

Hi All,

 

My server Details:

 

Hardware: ProLiant DL385 G7

OS: RHEL 5

RAID cotroller: HP Smart Array P410i Controller

HDDs: Four disks with 600GB (each)

 


RAID 0 is configured:

 

# cat /proc/driver/cciss/cciss0
cciss0: HP Smart Array P410i Controller
Board ID: 0x3245103c
Firmware Version: 3.66
IRQ: 162
Logical drives: 1
Sector size: 2048
Current Q depth: 0
Current # commands on controller: 0
Max Q depth since init: 159
Max # commands on controller since init: 159
Max SG entries since init: 31
Sequential access devices: 0

cciss/c0d0:      600.09GB       RAID 0

 

 

Only one HDD is used in RAID 0:

 

# hpacucli controller slot=0 physicaldrive all show

 

Smart Array P410i in Slot 0 (Embedded)

   array A

      physicaldrive 2C:1:1 (port 2C:box 1:bay 1, SAS, 600 GB, OK)

   unassigned

      physicaldrive 2C:1:2 (port 2C:box 1:bay 2, SAS, 600 GB, OK)
      physicaldrive 2C:1:3 (port 2C:box 1:bay 3, SAS, 600 GB, OK)
      physicaldrive 2C:1:4 (port 2C:box 1:bay 4, SAS, 600 GB, OK)

 

 

My Questions:

 

1)Can I change RAID configuration with out data loss like RAID 1 / RAID 5?

 

2)Can we include other HDDs in to existing RAID 0?

 

3)If we can not include other HDDs in to existing RAID 0, then how can we use those HDDs (hdd space)?

 

 

Please use plain text.
Honored Contributor
Matti_Kurkela
Posts: 6,271
Registered: ‎12-02-2001
Message 2 of 2 (1,671 Views)

Re: How to change RAID level in production server (Hardware RAID)

1.) Maybe: if your Smart Array P410i has a write cache unit installed, it can convert the RAID set to another RAID level without loss of data if the disk configuration is appropriate for the new RAID level. Some conversions *may* be possible without the write cache unit, too: I don't remember the exact details (check the SmartArray documentation).

 

To see if your Smart Array includes a write cache unit, please run:

# hpacucli controller slot=0 show config detail

 ...and see if it includes any mention about write cache (either BBWC or FBWC).

 

2.) Yes, the extension of the existing RAID array to new disks is possible.

 

3.) You could use the unassigned disks to form one or more new arrays (e.g. a single three-disk RAID 5 or RAID 0 array, or one RAID 1 mirror set + one single non-RAID disk, or even three separate one-disk "arrays").

 

All these can be done with hpacucli, but the web-GUI-based ACU tool might be easier to use.

 

Step-by-step procedure for the ACU available here:

http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/mostViewedDisplay/?sp4ts.oid=390...

 

The main document for hpacucli and the graphical ACU:

http://h20565.www2.hp.com/portal/site/hpsc/template.BINARYPORTLET/public/kb/docDisplay/resource.proc...

MK
Please use plain text.
The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation