2650 - Port Blocked by LACP (4681 Views)
Reply
Advisor
Søren Fisker
Posts: 29
Registered: ‎07-28-2002
Message 1 of 9 (4,681 Views)
Accepted Solution

2650 - Port Blocked by LACP

Procurve 2650, firmware H.07.50, Rom H.07.01

Most ports randomly log something like this:

I 10/05/04 11:35:13 ports: port 13 is now off-line
I 10/05/04 11:35:15 ports: port 13 is Blocked by LACP
I 10/05/04 11:35:17 ports: port 13 is now on-line

Is there any way to stop this?
Disable LACP?
Please use plain text.
Esteemed Contributor
SCOOTER
Posts: 281
Registered: ‎04-01-2003
Message 2 of 9 (4,681 Views)

Re: 2650 - Port Blocked by LACP

SÃ REN,

Log into the switch over console or telnet. Then in the CLI type the following commands:

2650# config t
2650(config)# no interface all lacp
2650(config)# write mem
2650(config)# show lacp

The response from the switch should be "no LACP ports found".

Kind regards,

SCOOTE
Please use plain text.
Advisor
Søren Fisker
Posts: 29
Registered: ‎07-28-2002
Message 3 of 9 (4,681 Views)

Re: 2650 - Port Blocked by LACP

Is there any documentation of the entire CLI interface somewhere?
Please use plain text.
Frequent Advisor
Eirram_1
Posts: 39
Registered: ‎01-02-2001
Message 4 of 9 (4,681 Views)

Re: 2650 - Port Blocked by LACP

Hello Soren,

No, there is no comprehensive CLI guide for the 2524 switch. Most of the commands will have to be gleaned from the manual(s).

Eirram
Please use plain text.
Advisor
Søren Fisker
Posts: 29
Registered: ‎07-28-2002
Message 5 of 9 (4,681 Views)

Re: 2650 - Port Blocked by LACP

Actually there _IS_ a "CLI interface reference guide" for 2524, but not 2650 or 2824.

;-)
Please use plain text.
Occasional Visitor
Andrew J. White
Posts: 2
Registered: ‎03-21-2006
Message 6 of 9 (4,681 Views)

Re: 2650 - Port Blocked by LACP

Ok, so where is the CLI reference guide for the 2524? I sure as heck cannot find it anywhere online after an hour of searching hp.com and google.
Please use plain text.
Trusted Contributor
Sergej Gurenko
Posts: 160
Registered: ‎11-13-2003
Message 7 of 9 (4,681 Views)

Re: 2650 - Port Blocked by LACP

start you searching under www.hp.com/rnd
Please use plain text.
Occasional Visitor
Andrew J. White
Posts: 2
Registered: ‎03-21-2006
Message 8 of 9 (4,681 Views)

Re: 2650 - Port Blocked by LACP

Yep, did that. I still cannot find it. Why not post the URL for all? :)
Please use plain text.
Esteemed Contributor
SCOOTER
Posts: 281
Registered: ‎04-01-2003
Message 9 of 9 (4,681 Views)

Re: 2650 - Port Blocked by LACP

You'll find it under the manual section for the 2300-2500 then check under previouse manuals.

And the URL is:

http://www.hp.com/rnd/pdfs/CLI_reference.pdf

Regards,

SCOOTER

Please use plain text.
The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation