HP NNMi 9.10: SPI Traffic can not get data from devices (988 Views)
Reply
Regular Advisor
quyenta
Posts: 190
Registered: ‎08-10-2008
Message 1 of 9 (1,151 Views)

HP NNMi 9.10: SPI Traffic can not get data from devices

Hi Experts,

 

I'm using NNMi 9.10 and spi Performance Traffic in the same server ( on Windows). I did configure following these steps:

 

NNMi server:

 

- Enable spi for traffic, configuring "leaf collector" for 2 vendor are cisco and Juniper ( pls see detail in attachment). Then started them and Running is ok.

 

Network devices:

 

-  Cisco: using command

 

(config)#interface FastEthernet 0/0
(config)#ip route-cache flow
(config)#exit
(config)#ip flow-export destination <Ip NNMi server> 9996
(config)#ip flow-export source FastEthernet 0/0
(config)#ip flow-export version 5
(config)#ip flow-cache timeout active 1
(config)#ip flow-cache timeout inactive 15
(config)#snmp-server ifindex persist

 

- Juniper (ex4200):

et protocols sflow collector  <Ip NNMi server> udp-port 6343
set protocols sflow interfaces ge-0/0/0.0
set protocols sflow interfaces ge-0/0/1.0
set protocols sflow polling-interval 5
set protocols sflow sample-rate 100

 

 

After that, I'm using Wireshark software testing recived from NNMi server, It can recive sflow package from juniper devices. But on NNMi server can not get any traffic from devices, got error" No data available"

 

 

Please help me solve this problem.

 

Thanks in advance.

 

Regular Advisor
quyenta
Posts: 190
Registered: ‎08-10-2008
Message 2 of 9 (1,144 Views)

Re: HP NNMi 9.10: SPI Traffic can not get data from devices

Anyone can give some suggestions ?

Respected Contributor
Bharath M R
Posts: 410
Registered: ‎03-10-2010
Message 3 of 9 (1,133 Views)

Re: HP NNMi 9.10: SPI Traffic can not get data from devices

hii..

 

 

      try by giving port 9995 for sflow.

Thanks,
Bharath
Regular Advisor
quyenta
Posts: 190
Registered: ‎08-10-2008
Message 4 of 9 (1,113 Views)

Re: HP NNMi 9.10: SPI Traffic can not get data from devices

Hi experts,

 

How long NNMi spi for Traffic get data flow from devices? after configuring Traffic or some hours later ?

Regular Advisor
quyenta
Posts: 190
Registered: ‎08-10-2008
Message 5 of 9 (1,091 Views)

Re: HP NNMi 9.10: SPI Traffic can not get data from devices

Hi experts,

 

The NNMi stored flow packets following :

<Data_Dir>\shared\traffic-leaf\data\<Leaf_Collector_Instance>\<IP_Address_of_Source>

That meaning Leaf Collector works well. So maybe the problem here is “Master Collector”. NPS server can not get data from Master Collector that why NPS can not create Report. The report get error “ No data available”

 

Could you give any troubleshooting for this problem?

Regular Advisor
quyenta
Posts: 190
Registered: ‎08-10-2008
Message 6 of 9 (1,024 Views)

Re: HP NNMi 9.10: SPI Traffic can not get data from devices

Have anyone can give me some suggestions in this case?

Occasional Advisor
tagrawal
Posts: 22
Registered: ‎05-30-2012
Message 7 of 9 (1,010 Views)

Re: HP NNMi 9.10: SPI Traffic can not get data from devices

[ Edited ]

Hi,

 

Configure two different leaf collector:

 

1) For Cisco , Collector type : netflow,  Listen port: 9996

2) For Juniper, Collector  type : sflow,  Listen port: 6343

 

In ip: provide the ip address where you have installed leaf

 

I hope this is helpful.

 

Regards,

Tarun

 

Occasional Advisor
rodarcqu
Posts: 5
Registered: ‎07-27-2011
Message 8 of 9 (988 Views)

HP NNMi 9.10: SPI Traffic can not get data from devices

Hi,

 

In order to make sure that you are getting traffic from those devices please install wireshark or tcpdump and make a filter of the IP address of the devices if you wanted to be more specifict please add the port in the filter.

 

Best Regards,

HP Expert
iquesada
Posts: 224
Registered: ‎03-07-2012
Message 9 of 9 (983 Views)

Re: HP NNMi 9.10: SPI Traffic can not get data from devices

Hi,

 

Also you can check the following:

 

1. That the ports between master and leaf have been opened and firewalls are not interfering in leaf-master communication.
2. That the leaf collector port listening for netflow packets is open using netstat

3. If flows are being exported to leaf using Wireshark/tcpdump on the leaf system

 

BR,

HP Support
The views expressed in my contributions are my own and do not necessarily reflect the views and strategy of HP.
If you find this or any post resolves your issue, please be sure to mark it as an accepted solution, If you are satisfied with anyone’s response please remember to give them a KUDOS and show your appreciation.
The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation.