09-07-2008 10:33 AM
I have a Laserjet 2840 running via Mac OS X.
I was installing the firmware software from the HP site.
We had a power cut midway through installation.
Turned the machine back on, now reads the error on the printer: 'Firmware Corrupt Ready 2 Download"
My computer cannot see my printer and it will not restrat.
09-09-2008 04:58 AM
11-10-2008 09:03 PM
I know how to solve this problem.
First you must turn your M1522xx on and if it shows "Firmware Corrupt Ready 2 Download", that's what we need.
If LCD screen is blank, then clear all tasks for this printer and delete its driver from "Printers and Faxes". Now turn it off and on again. Do it untill "Firmware Corrupt Ready 2 Download" shows.
When we see "Firmware Corrupt Ready 2 Download" we should do as follows:
1) TURN PRINTER'S POWER OFF
(USB should stay connected)
2) Delete installed driver (if exists)
3) Manually install driver for M1522xx
(When choosing port, use one of "Virtual Printer Ports for USB" which is your printer connected to)
4) Run firmware update program from HP Support web page (PRINTER IS OFF)
5) In firmware update program's window choose your printer (manually installed) and press "Send Firmware" button
6) Wait for firmware to be completely sent to your printer's task window
7) TURN YOUR PRINTER ON
8) First you will see "Firmware Corrupt Ready 2 Download" message. If there is no such message, turn off and on again untill it shows. Then message will change to "Downloading...", "Erasing..." and "Programming..."
9) When all this operations end, printer'll ask you to turn it off and on.
That's all. No need to contact HP Support or buy any parts.
P.S. While "Downloading...", "Erasing..." or "Programming...", printer may hang. It's not fatal. Just repeat all operations again.
To prevent hangs use quality USB cable when updating firmware.
P.P.S. Sorry for bad english. I'm russian...
03-24-2010 04:44 AM
Did you recommend anything?
05-06-2010 03:34 AM
You must install your hp m1522nf printer driver manually,run update software,click on send firmware tab and wait for done.
before that you must remove the left cower of printer,you will see one free jumper,place a jumper P109. turn on printer,on display you will see "BOOTDIMM" in first line,second line ready 2 download,just for that wait for done.
10-23-2011 03:47 PM
I would add that you may need send the firmware several times for a successful transfer and once it is complete you will receive a message "Permanent Storage Init" for a couple of minutes, then the printer will restart a few times before the process is complete. The firmware upgrade process (downloading, erasing, programming) should happen fairly quickly without any significant delays (greater than a minute) if it does then the process is hanging and you need to send the firmware again.
07-23-2012 05:19 PM
After running the firmware upgrade, the process remains stuck in "erasing..." forever. I quit after a dozen attempts. The printer is a LaserJet CP1525nw Color. OS is Windows 7 64-bit
12-06-2012 08:26 PM - last edited on 06-27-2013 02:25 AM by RASHMI
Hello ladies and gentlemen,
Unfortunately I am also having the same problem after trying to upgrade the firmware of my CP1525nw came the nasty surprise!
First message: "CORRUPT FIRMWARE READY 2 DOWNLOAD" and then the other: "ERASING >>>>>>>>>>>>>>>" and then never left ... I'm almost a week still, with services late and nobody gives me a light.
The funny thing is that I called in Support of Hp and made me a lot of questions and for registration etc ... but in the end did not solve anything and if your machine is not under warranty they do not give you much attention, and that looks I have little more than a year of use.
Then at the end of the link me told me to contact a technician to my confidence to try to solve the problem.
How can I have a coach I trust if I never needed repairs on any printer in my life? Does anyone have the phone number of such technical confidence? Is JOKE right?
Only have one little problem, the service technician is not free and will cost, then it leads me to believe that this upgrade procedure is being done to damage our equipment! For me nothing but a trap, which is good because upgrade did not update just crashed.
How can we afford an expense being that the error is not ours?
We just got in the Official website of HP found that there was an update to be made, there was saying it was highly recommended to indicate that if we did this firmware update the machine would perform better and looks just as it did! Now here we are, with our printers stops!
A company in the global market so important to let this happen to your users, it really is absurd and a total disregard, I think it is a case of police (law).
Let us mobilize and try to do something about it, next week I will tell to justice here in my state about
what can be done to make this humiliating situation is resolved and will not happen again with other consumers.
If anyone wants me I'll be back in the waiting!
I really hope some measure / solution to this problem.
Manifesto here wishes for much indignation and once again I am grateful for the attention,
12-07-2012 12:49 AM
You're obviously not happy but a public forum is not the place to make what appear to be threats or rally calls to the masses.
Try calling Samsung, IBM, or any other company for a product that is out of warranty and you get the same response, why should HP be any different ?
You say an engineer will be at a cost, so are any other companies, one Major Satelite company wanted £250 to send an engineer to fault find at my house for the same reasons you state.
You're simply making a noise in an effort to get something for nothing, I notice you don't put the purchase date of your printer on the post ?
I would expect your post will be deleted as in fairness it carrys threats and accusations that if you cannot uphold them would place you at the point of litigation, not HP.
You say the firmware update is put on the web deliberately to damage equipment, this is slander and could make you liable for any damage caused by your statement.
This forum is a public forum, it's not HP tech support, you perhaps need to think on how you are going to say what you need to say before you put it on here.
Written word is legally binding so you're not helping yourself resolve this issue.
At the end of the day perhaps the worst scenario would be you need to replace your formatter or any firmware Dimm, hardly a high cost and certainly much cheaper than if you have opened yourself to any repercussions by making accusations.
I don't work for HP, but I've been a HP certified engineer for 30 years so my comments are my own.
(Don't forget Kudos if people have helped)
06-26-2013 08:16 PM
O que eu estou apenas querendo dizer é que eu simplesmente fui informado pelo site da HP a fazer a atualização da impressora pelo próprio site, que isso traria benefícios quanto ao desempenho da impressora e o mesmo danificou permanentemente o equipamento que até então estava em perfeito funcionamento.
Será que tem como entender isso? Isso caracteriza dano material!
Não quero fazer aqui apologia a nada, só quero minha impressora funcionando novamente porque parece que ninguém escuta, mas eu vou repetir: A culpa não foi minha.
O pior é ter que ficar ouvindo essas baboseiras todas sem nenhuma solução plausível.
E ainda tem mais, já levei até um técnico especializado e fui informado de que o problema e com a placa lógica e eles não tem a peça para reposição e não consigo encontrá-la em nenhuma loja.
Onde consigo consertar minha impressora? Me dê um lugar, um número, qualquer coisa em Brasília-DF!
E você ainda vem me dizer que obviamente não sou feliz. Certamente não sou, pois minhas contas estão atrasadas, contas essas que pagava com o serviço de minha impressora que comprei com tanto sacrifício e que já esta danificada há quase 08 meses sem solução.
Pague minhas contas e quem sabe eu volte a ser uma pessoa feliz!
06-27-2013 02:06 AM
Thanks for using HP Forums!
We would like to encourage that this discussion should be continued in English language as this forums is a English construct-based communities as per the rules of participation (Rules(9) *see below for the url). Your post in English format will definitely help your other fellow participants to well-understand the issues and help you out regarding this.
HP Forums also supports few other languages for the same where you can select the language option located at the top right side of the EBC main page.
12-18-2013 05:42 AM
Our HP M2727nf has hung after a firmware update attempt.
I can get it (OK+Cancel during startup) to display "Bootdimm ready 2 Download" but when attaching the printer via USB, Win 7 displays it as an "Unknown Device" (generic USB hub, working properly). So I can't select it as a receiver of the firmware. Installing the driver, e.g. HP Universal Print Driver for Windows PCL6, doesn't change this.
The USB port number is Port_#0006.Hub_#0005
Is there a way around this?
Help much appreciated,
Erik from Sweden
01-06-2014 12:57 AM - edited 01-06-2014 12:59 AM
I have HP printer model M451nw all your instuction i fallow how to update the firmware corrupted ready 2 download from the start is ok when thetime erasing comes stop here ill tryed several time but still stop in the erasing. You have other option how to solve my problem. Thank you
11-03-2014 09:15 AM
Like the original individual who started this post, I, too, ran the Firmware Update on a Mac (Mac with 10.8 OS). The firmware update quit in the middle with an error message. When I powered off and back on the printer, the printer display said "Fatal Error 1! Call HP Support" and after a second restart, the printer displayed, "Firmware Corrupt Ready 2 Download."
At this point, I switched from a Macintosh computer to a Windows computer to try Kodiak's suggestions. Thank you, Kodiak. Your solution was great and worked for a HP LaserJet M1522nf. And also, thank you alexisjohn for the comments about running the Firmware Update a few times if it hangs up. I was glad that you mentioned the "Permanent Storage Init" printer display message.
Also, I had to use the HP CD that came with the printer, and I ran the Uninstall Utility to completely get rid of the software and drivers before I started Kodiak's steps. On the HP M1522 CD (right click and Open)> util folder > CCC folder, and I ran Uninstall_L4 to get rid of all traces of the printer's software. Restarted computer, and then began Kodiak's steps.