script error (628 Views)
Reply
Honored Contributor
parkar
Posts: 2,321
Registered: ‎01-23-2010
Message 1 of 4 (628 Views)

script error

while running script from vugen

 

we are getting error for oracle form based application throught protocol oracle web application.

 

New_Contact.c(219): nca_java_action("281","resourceRequest")
New_Contact.c(221): Checking for active timers...
New_Contact.c(221):     No timers found, exiting.
New_Contact.c(221): Add to flush terminate message
New_Contact.c(221): nca_java_action("281","msgRequested")
New_Contact.c(223): nca_step_end: terminate message
New_Contact.c(223): Timer is already in use -> could not be scheduled twice
New_Contact.c(223): No timers in queue -> nothing to schedule

 

script not getting proceed at above steps

 

any suggestions

 

Cheers!

Nvr Blame a day in ur life....... Good day gives "happiness" & Bad day gives "experience" ......
HP Expert
Suerte13cr
Posts: 736
Registered: ‎09-14-2011
Message 2 of 4 (624 Views)

Re: script error

Hi Parkar,

 

Try what is mentioned in this article:

http://support.openview.hp.com/selfsolve/document/KM1258034

 

Regards,

Mario

HP LR/PC Support

If you are customer you can try posting on our internal forums for more personalized support.

LoadRunner:
http://h30499.www3.hp.com/t5/LoadRunner-Support-Customer/bd-p/loadrunner-support-customer-forum

Performance Center:
http://h30499.www3.hp.com/t5/Performance-Center-Support/bd-p/performance-center-support-customer

How to:
http://www.youtube.com/watch?v=4ChlysWupWM

If you find that this or any post resolves your issue, please be sure to mark it as an accepted solution.
Frequent Visitor
sandyaveduri
Posts: 2
Registered: ‎10-07-2012
Message 3 of 4 (503 Views)

Re: script error

Hi Mario, I am not able to view the link provided.Can you please send me the doc to my  mail  sandhya.hanny@gmail.com.

or else please suggest me a solution?

 

Cheers

HP Expert
Suerte13cr
Posts: 736
Registered: ‎09-14-2011
Message 4 of 4 (499 Views)

Re: script error

This is what is mentioned for solution:

 

Set the NCA time as follows:

  1. Close VuGen.
  2. Set the NCATimerWaitMode=0,1,2,3 in the default.cfg file in the script folder.
        You can set different values but at a time only ONE value.
        Default value is 0.
  3. Open VuGen and open script.
  4. Replay the script.
  5. At least one of the value should help and script should replay fine.

In Runtime Settings, try the following:

Oracle NCA ---> Client Emulation --> Uncheck “Enable heartbeat” --> This is a good practice. 

 
Regards,

Mario M.

HP LR/PC Support

If you are customer you can try posting on our internal forums for more personalized support.

LoadRunner:
http://h30499.www3.hp.com/t5/LoadRunner-Support-Customer/bd-p/loadrunner-support-customer-forum

Performance Center:
http://h30499.www3.hp.com/t5/Performance-Center-Support/bd-p/performance-center-support-customer

How to:
http://www.youtube.com/watch?v=4ChlysWupWM

If you find that this or any post resolves your issue, please be sure to mark it as an accepted solution.
The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation.