Kernel: Network packet flooding detected. (2129 Views)
Reply
Occasional Advisor
Dennis Devore_1
Posts: 11
Registered: ‎09-03-2009
Message 1 of 8 (2,129 Views)
Accepted Solution

Kernel: Network packet flooding detected.

I am recieving this "Kernel: Network packet flooding detected." error a few times per day. This is being reported on my c7000 in the log. When this occurs all of my blade servers (bl460 g1) peg 100% utilization for about 30 seconds, then return to normal. Trying to resolve this I updated my onboard admin to 2.6 from 2.52. The iLo versions on the blades are all 1.78.

Any suggestions??
Please use plain text.
Honored Contributor
HEM_2
Posts: 332
Registered: ‎10-07-2004
Message 2 of 8 (2,128 Views)

Re: Kernel: Network packet flooding detected.

Dennis:

This means that there is excessive traffic being seen on the OA/ILO network port that connects to the rest of your network.

Do you have a separate management VLAN for the OA/ILOs? That would be a good idea to isolate the OA/ILO's from your normal production traffic.

Otherwise check for excessive broadcast/multicast traffic or unicast flooding on your network. Excessive Unicast Flooding can be caused by spanning tree topology changes as everytime a spanning tree topology change occurs the mac address tables of your switches are flushed and everything is flooded until it is relearned.

For multicast try to use IGMP snooping.

take a network trace to identify the nature of your excessive traffic.
Please use plain text.
Occasional Advisor
Dennis Devore_1
Posts: 11
Registered: ‎09-03-2009
Message 3 of 8 (2,129 Views)

Re: Kernel: Network packet flooding detected.

Thanks for the info! I have found that it does appear to be related to traffic on the core switch, I have not yet setup a separate vlan for the iLo management, but plan on doing this soon.

Currently spanning tree is off on this switch. Would using a product such as wire shark to trace traffic be sufficient?

Thanks!
Dennis
Please use plain text.
Honored Contributor
HEM_2
Posts: 332
Registered: ‎10-07-2004
Message 4 of 8 (2,129 Views)

Re: Kernel: Network packet flooding detected.

yup, wireshark would do just fine....

Please use plain text.
Occasional Contributor
CA-Blademan
Posts: 5
Registered: ‎03-29-2009
Message 5 of 8 (2,129 Views)

Re: Kernel: Network packet flooding detected.

FYI everybody - This issue has not been fixed by HP. It has happened in our environment in v2.21, v2.25, v2.41, v2.32, v2.51, and v2.52 and continues to happen. I believe is a hardware issue. Make note that HP considers these OA's obsolete now. They are now pushing the Gigbyte version now.
Please use plain text.
Honored Contributor
marcus1234
Posts: 979
Registered: ‎11-23-2008
Message 6 of 8 (2,130 Views)

Re: Kernel: Network packet flooding detected.

dennis what is the HP case number
Please use plain text.
Advisor
Dnortham
Posts: 10
Registered: ‎11-05-2009
Message 7 of 8 (2,129 Views)

Re: Kernel: Network packet flooding detected.

I am having same issue; HP advised to have OA port on seperate VLAN than rest of Blades, HP advised that the OA is getting hit "hard" but not seeing the traffic on the cisco switch side nor blade side.

running OA 2.60 and vc 2.30 firmware

Please use plain text.
Honored Contributor
HEM_2
Posts: 332
Registered: ‎10-07-2004
Message 8 of 8 (2,129 Views)

Re: Kernel: Network packet flooding detected.

This message gets logged to the OA System Log when a certain packet per second threshold is detected on the OA NIC. I'm not certain but I've heard that the threshold is something like 10000 packets over a two-second period.

This can be verified with a protocol analyzer listening to the OA/ILO port.

I looked around in the OA 2.60 GUI and CLI to see if there was a threshold that could be adjusted but couldn't find anything...
Please use plain text.
The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation