Re: How to save GSP Lan settings (268 Views)
Reply
Occasional Contributor
hughf15
Posts: 4
Registered: ‎03-27-2013
Message 1 of 6 (276 Views)

How to save GSP Lan settings

[ Edited ]

How do I save GSP Lan setting so that I don't have to reset them all over again after shutdown/reboot? I am using Putty to capture the log when boot but each time I have to do this.

 

 

thanks

 

hugh

 

 

P.S. this thread has been moved from HP-UX > General to Servers > HP 9000 - HP Forums Moderator

 

Please use plain text.
Acclaimed Contributor
Torsten.
Posts: 23,200
Registered: ‎10-02-2001
Message 2 of 6 (269 Views)

Re: How to save GSP Lan settings

What server model?


Hope this helps!
Regards
Torsten.

__________________________________________________

There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________

No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! star in the left column!   
Please use plain text.
HP Pro
pradeep m
Posts: 154
Registered: ‎12-08-2010
Message 3 of 6 (268 Views)

Re: How to save GSP Lan settings

From the GSP console, run LS command to display GSP LAN settings

GSP:CM> LS

 

To configure GSP LAN setting, run LC command from GSP

GSP:CM> LC

 

For additional details refer the Service Console (GSP or MP ) User Guide.

Click here to access Service Console (GSP or MP) User Guide.

Regards,
Pradeep

I am an HP Employee
Please use plain text.
Acclaimed Contributor
Torsten.
Posts: 23,200
Registered: ‎10-02-2001
Message 4 of 6 (265 Views)

Re: How to save GSP Lan settings

No CM in GSP.

From GSP prompt run LC (LAN config).

Each modification will be saved without additional command. When finished, reboot the GSP.

GSP> xd



XD


Non destructive tests :

1. Parameters checksum

2. I2C access (get Power Monitor status)

3. LAN access (PING)

4. Modem selftests

5. Secondary I2C access (get System status)


Type R to reset the GSP or Q to quit the diagnostic menu.


-> Choice: r

r


The GSP is now being reset...

HP Guardian Service Processor

Hope this helps!
Regards
Torsten.

__________________________________________________

There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________

No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! star in the left column!   
Please use plain text.
Honored Contributor
Patrick Wallek
Posts: 13,733
Registered: ‎06-21-2000
Message 5 of 6 (263 Views)

Re: How to save GSP Lan settings

A simple reboot of a server should not cause a loss of the GSP lan settings.  

 

However, if you power off the server, or lose power to the server, and the GSP lan settings disappear, then the battery on the GSP card is likely dead and needs to be replaced.

Please use plain text.
Occasional Contributor
hughf15
Posts: 4
Registered: ‎03-27-2013
Message 6 of 6 (258 Views)

Re: How to save GSP Lan settings

our model is RP2430. I did as Torsten said. I am trouble-shooting and need to replace an io card. I did remove the power cord since I need to take it out of the rack. But each time I have to set the Lan settings. I will replace the battery on the GSP as Patrick has suggested. Thanks everyone!

Please use plain text.
The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation