12-06-2010 08:21 AM
Restarted the server but nothing , these were the disk of mirror. But now they ar not blinking red and FSDMN not showing as they say
showfsets: can't show fileset info for domain 'database_dmn'
showfsets: error = I/O error
Replacing any of the hard drives could solve the problem.
The mirror consists of two HDD
12-06-2010 12:13 PM
You've given us very little to go on...
How are/were the drives mirrored ?
Any RAID controllers, if so what type ?
The output of:
# sizer -v
# hwmgr view dev
# ls -l /etc/fdmns/database_dmn
would be useful to see...
From the SRM prompt (P00>>>) the output of the commands
would be useful too.
12-06-2010 01:56 PM
The system is 5.1B-4
the link inside database_dmn is "dsk2a"
but I cannot post anything else from the other commands.
I can do that tomorrow morning when I get back to work.
Tomorrow I am thinking placing only one new drive on the server and retry?
Or you have any other idea?
I dont know anything about RAID on this system, but as I see it is not done through LSM
The system has 6 HDD 36GB divided in three mirrors , two in each one. so the Disk2 has error. the other disks are reporting ok.
12-06-2010 02:12 PM
OK, post the information when you can...
Personally I wouldn't touch any hardware until you've determined exactly what has broken.
There are a number of different RAID cards that go in a DS20E...
12-06-2010 11:37 PM
46: /dev/disk/floppy0c 3.5in floppy fdi0-unit-0
63: /dev/disk/dsk0c i2o_bs iop-0-dev-0
64: /dev/disk/dsk1c i2o_bs iop-0-dev-1
65: /dev/disk/dsk2c i2o_bs iop-0-dev-2
66: /dev/disk/cdrom0c TEAC CD-224E bus-1-targ-0-lun-0
69: /dev/ntape/tape0 COMPAQ SDT-10000 bus-0-targ-6-lun-0
When I will be at the console I can post the results of other commands
12-07-2010 02:42 AM
As you suggest I executed the comand "show dev" and the output is:
dqa 0.0.0.105.0 DQA0 CD-224E 9.9A
mka600.6.0.7.1 MKA600 compaq SDT-10000
eia0.0.0.3004 EIA0 00-0B-CD-BA-F4-54
eia0.0.0.3005 EIB0 00-0B-CD-BA-F4-55
PKA0.7.0.7.1 PKA0 SCSI BUSS ID 7
PKB0.7.0.6.1 PKC0 SCSI BUSS ID 7
PKC0.7.0.106.1 PKC0 SCSI BUSS ID 7
The output of "Show config" command is:
SRM console V6.4-11
Processors CPU0, CPU1 both Alpha EV68H 2.2 833 MGH
Memory 1 GB
Bus 00 slot 06/0 Adaptec AIC-7895 pkb0.7.0.6.0 SCI Bus ID 7
Bus 00 slot 06/1 Adaptec AIC-7895 pkc0.7.0.106.0 SCI Bus ID 7
Bus 00 slot 07: NCR 53C895
pka0.7.0.7.0 SCI Bus ID 7
mka 600.6.0.7.1 Compaq STD-10000
Thank you in advance,
12-14-2010 05:33 PM
have you tried to boot the server in single user mode
>>> b -fl s
12-15-2010 03:03 PM
device is a KZPCC Raid controller.
So 6 physical drives - 3 mirrors - 3 logical
You should be able to boot into the KZPCC
configurator from the >>> prompt, find out which drive has failed and then replace it.
Regards, John Welsh.
12-16-2010 03:48 AM
but 3 disks seem to fail.
2 of them are forming one logical drive and with that i might be that data is lost.
I am trying to recover but i think there might be any corruption on the controler, because there is two low possibility to have three disks failed at once.
I think i will remove the controller the batery jus for 5 min. and the put it again also a firmware upgrade
if any other idea please inform me
12-16-2010 04:38 AM
Have you run the RAID controller configuration utility to see what state it thinks it is in ?
It has been a while since I've used a KZPCC, but I think you launch the utility from the SRM with:
P00>>> run bios pza0
You should find more help here:
12-16-2010 07:16 AM
1. Updatet firmware to CQ17
2.I removed the KZPCC adapter and pulled out the battery and let it for 5 min. and then plug in.
Now in SMOR before there were 2 failed HDD now one is failed and the other with status "impacted" but RAID still "DEAD"
Anyone has any experience with these situation??