Re: Can't Boot tru64 server [boot failure] can't open osf_boot halt code=5 (530 Views)
Reply
Occasional Visitor
burakofluoglu
Posts: 1
Registered: ‎02-21-2013
Message 1 of 3 (603 Views)

Can't Boot tru64 server [boot failure] can't open osf_boot halt code=5

Following is the faulty node that i can not boot up.

Please comment if you have experienced the issue before. 

 

P00#SMC1>>>sho device
dga30.1001.0.2.1 $1$DGA30 COMPAQ MSA1000 VOLUME 4.32
dgb30.1002.0.2.3 $1$DGA30 COMPAQ MSA1000 VOLUME 4.32
dka0.0.0.1.2 DKA0 COMPAQ BF03688284 HPB2
dka100.1.0.1.2 DKA100 COMPAQ BF03688284 HPB2
dqa0.0.0.16.0 DQA0 HL-DT-ST RW/DVD GCC-4481 2.05
dva0.0.0.1000.0 DVA0
mka400.4.0.1.2 MKA400 HP C7438A V312
ega0.0.0.5.2 EGA0 00-02-A5-C6-22-E3
eia0.0.0.8.0 EIA0 00-02-A5-20-2E-C9
eib0.0.0.2004.1 EIB0 00-13-21-08-03-20
eic0.0.0.2005.1 EIC0 00-13-21-08-03-21
pga0.0.0.2.1 PGA0 WWN 1000-0000-c948-a7fe
pgb0.0.0.2.3 PGB0 WWN 1000-0000-c948-a54f
pka0.7.0.1.2 PKA0 SCSI Bus ID 7
pkb0.7.0.101.2 PKB0 SCSI Bus ID 7
P00#SMC1>>>
P00#SMC1>>>
P00#SMC1>>>show boot_reset
boot_reset ON
P00#SMC1>>>
P00#SMC1>>>
P00#SMC1>>>boot
Initializing...


OpenVMS PALcode V1.98-42, Tru64 UNIX PALcode V1.92-33

*** keyboard not plugged in...
starting console on CPU 0
initialized idle PCB
initializing semaphores
initializing heap
initial heap 240c0
memory low limit = 222000 heap = 240c0, 17fc0
initializing driver structures
initializing idle process PID
initializing file system
initializing timer data structures
lowering IPL
CPU 0 speed is 1000 MHz
create dead_eater
create poll
create timer
create powerup
access NVRAM
2048 MB of System Memory
Testing Memory
...
probe I/O subsystem
Hose 0 - PCI bus running at 33Mhz
entering idle loop
Hose 1 - PCI bus running at 66Mhz
Hose 2 - PCI bus running at 66Mhz
Hose 3 - PCI bus running at 66Mhz
starting drivers
starting console on CPU 1
initialized idle PCB
initializing idle process PID
lowering IPL
CPU 1 speed is 1000 MHz
create powerup
initializing GCT/FRU at 24a000
Initializing ega dqa dqb eia eib eic pga pgb pka pkb
Memory Testing and Configuration Status
Array Size Base Address Intlv Mode
--------- ---------- ---------------- ----------
0 1024Mb 0000000000000000 1-Way
1 1024Mb 0000000040000000 1-Way

2048 MB of System Memory
Testing the System
Testing the Disks (read only)
Testing the Network
AlphaServer DS25 Console V6.8-18, built on Jul 30 2004 at 09:28:29

CPU 0 booting

(boot dka100.1.0.1.2 -flags A)
block 0 of dka100.1.0.1.2 is a valid boot block
reading 19 blocks from dka100.1.0.1.2
bootstrap code read in
base = 51a000, image_start = 0, image_bytes = 2600(9728)
initializing HWRPB at 2000
initializing page table at 7fff0000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
can't open osf_boot

halted CPU 0

halt code = 5
HALT instruction executed
PC = 20000030
boot failure
P00#SMC1>>>

 

 

Thanks,

Burak.

Please use plain text.
Occasional Visitor
Srikanth B K
Posts: 2
Registered: ‎12-15-2003
Message 2 of 3 (543 Views)

Re: Can't Boot tru64 server [boot failure] can't open osf_boot halt code=5

Hi

 

I know the original query was posted in Feb and it is April now .  Better late than never

 

I hope DKA100 is boot disk - it is 36 GB Local SCSI disk - Normally DKA0 is boot device - hence this confirmation

 

if DKA100 is correct - clearly, it is unable to load kernel - it is corrupted.  Try booting through CD/DVD - DQA0 and then restore back up / load OS

 

you may also attempt >>> B DKA0

 

With regards

Srikanth BK

 

 

Please use plain text.
Occasional Visitor
marlene lam
Posts: 3
Registered: ‎04-20-2010
Message 3 of 3 (530 Views)

Re: Can't Boot tru64 server [boot failure] can't open osf_boot halt code=5

search of the HP support center knowledge base for "osf_boot" yeilds a few answers, of note:
Tru64, V5.1X - Howto: restoring osf_bootISSUE: System will not boot: "Cannot open osf_boot".
V5.X
This example assumes no LSM, no RAID, and a standalone system.
SOLUTION: Common causes:
1.The osf_boot file may be missing, or corrupt(from a running V5.1 system).
# ls -al /osf_boot -rwxr-xr-x 1 root system 102496 Nov 28 12:21 /osf_boot
2.Is this the correct disk, it may be the wrong disk, maybe non-bootable ?
## Check BOOTDEF_DEV console variable.
3.Boot blocks for this disk have been destroyed, or corrupted.
4.Primary and Secondary bootstraps may be the wrong type( UFS vs. ADVFS).
## Check disklabel.
5.Possible filesystem corruption in root_domain.
## Run fixfdmn, or verify on root_domain.

6.Possible hardware problems

How to restore osf_boot
.... ( cdrom procedure .. )

hth,
Marlene
Please use plain text.
The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation