Mounting 2.5" and SSD Drives in xw6400, xw8400, xw6600, xw8600 - Favorite mounts

by Community Manager on ‎09-27-2012 07:44 AM

This essentially is a note about the best 2.5" to 3.5" drive/SSD adapters I have found for use with these HP workstations. 


The form factors of 2.5" hard drives and SSD's are very similar, and for our teleradiology work we have settled in on a Seagate "hybrid" 2.5" hard drive which is comprised of 500GB conventional drive, and 4GB of SSD-like flash memory that the drive loads with the most commonly used software components.  This is the 500GB version of the Momentus XT, with good review at this site:   Their new version, just released, is 750GB with 8GB flash.  It is more than we need for our purposes. also reviewed that new release.


This drive has given us a very significant improvement in performance over conventional drives.  Pure SSD drives are faster, but these fit our needs at much lower cost.  These don't need TRIM, and work equally well in our XPPro32-bit and W764-bit installs.  How to mount them in the HP green plastic sleds used in the xw workstations?  Use of a SSD would be virtually identical with these adapters, but noise is not an issue for them.


Attached are two pictures, one with 4 options and the drives out, and one with my favorite two adapters, with drives mounted, in the workstation.  The descriptions below refer to the pic with all four out of the workstation:



Favorite:  Top left, blue anodized strong aluminum alloy with the synthetic rubber blue grommets adding noise reduction in addition to the gray grommets built into the HP green plastic sled's metal attachment points.  Those metal attachment point pegs slip perfectly into the threaded holes in the blue aluminum extensions, and thereby this adapter also could be screwed into a conventional 3.5" hard drive bay.  Same for all the rest of them.  Name, source and cost:  This is an OWC Multi-Mount, with web site    and cost is $18.00.  Note that in pictures attached that it places the drive centered into the middle of the bay.



Second Favorite:  Top right, also from the same company, is a more rigid cast high quality metal frame with SATA to SATA adapter that centers the drive more to the left in the bay.  You can see in my second picture that the combo of the blue one above and the black one below lets the SATA cables hang nicely.  The short wires between the two power attachments are not having to be tight, either, with that arrangement.  I like the Molex brand latching red cables from, and I noticed that this one's SATA attachment at the rear end of the green circuit board SATA adapter did not have the lips that allow the latching latching mechanism to work.  They have a newer version out now with a red circuit board SATA adapter that may have that upgrade, but I am not sure on that.  The nice snug Foxconn SATA connectors that HP uses work great on that adapter.  The metal is nicely powder coated, high quality and the sides are slightly over 1/4" thick in height, so this is substantial.  The power coating is thick and insulates the bottom of the drive from the metal.  It is called the AdaptaDrive and the web site is    and the cost is $20.00. 


Third Favorite:  Bottom right, a Western Digital IcePack mounting frame, and those come with the Velociraptor 10k RPM drives which are 2.5" form factor, mounted in that frame to perfectly match a 3.5" form factor.  Those can be hard to find, but go for about $25.00, are heavy, and supposedly aren't so great in noise reduction.  Note how it shifts the power/SATA attachments to the left, similar to #2 above.  That can be handy rather than a detriment if you start with #1 above and #2 or #3 below.  PDF attached, from Western Digital.


Cheap, and it works:  Bottom left, and made by Thermaltake, a good name.  It has room to mount two stacked atop the other, but I mount only in the top position for good ventilation.  Note how the drive connectors are recessed forward towards the front of the HP green plastic sled.  You cannot use right angle SATA cables for these, but straight ones will work fine, and curve downwards to the motherboard out the rear of the drive bay.  This one is strong, cheap, and offers excellent venting.  It shifts the drive connectors towards the middle of the bay, as in #1 above.  It is fine if you only are going to use one drive total, or if you have both drives recessed this way, but the wire length between the top and the bottom drive power connectors is quite short, and to have one recessed and one out at the more normal position would be a tight fit.  That is the Thermaltake AC0014, $10.00 at


Those latching cables..... they come in 0.5 and 1.0 meter lengths, and are made by the Molex company, so you know the quality is excellent.  I get them from, and they have both straight-straight and right angle-straight ones, latching at each end.  These are about $2.50 each, and we don't have loose SATA connections if we use these.  Source is, and there is a PDF attached, with these cables at the bottom, and the right angle ones represented by figure Q at the top.  A+ quality, and they're on page 1359 of the Mouser catalog currently online.  The latching ribs are built into the top inside face of virtually all of the SATA connectors at the rear end of modern hard drives, SSD's and optical drives these days.

Showing results for 
Search instead for 
Do you mean 
HP Blog

Technical Support Services Blog


Follow Us
Twitter Stream
The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation.