Web Management with A5120-EI Series Switches available? (38245 Views)
Reply
Advisor
Posts: 28
Registered: ‎02-18-2004
Message 1 of 8 (38,245 Views)
Accepted Solution

Web Management with A5120-EI Series Switches available?

I'm using FW Release HP A5120EI-CMW520-R2208.

 

Is the Web Management over http with this FW release available?

How do I configure the access - what "service-type" do I have to configure?

Where do I find the documentation for Web Management?

 

I'm just getting a nice Login-Page...

 

With kind regards

Manfred

Advisor
Posts: 28
Registered: ‎02-18-2004
Message 2 of 8 (38,179 Views)

Re: Web Management with A5120-EI Series Switches available?

Just had to read the RIGHT Manual on the RIGHT Website (H3C)....

 

The only thing I have forgotten to configure was:

authorization-attribute level 3

 

The service-type is telnet.

 

I found the description for configuring the Web interface in the H3C S5120-EI Series Ethernet Switches
Fundamentals Configuration Guide: http://www.h3c.com/portal/Technical_Support___Documents/Technical_Documents/Switches/H3C_S5120_Serie... on page 61 (Chapter: Web login).

 

Configuration example for http access:
 
# Log in to the device via the console port and configure the IP address of VLAN 1 of the device. VLAN
1 is the default VLAN. 
<Sysname> system-view
[Sysname] interface vlan-interface 1
[Sysname-VLAN-interface1] ip address 192.168.0.58 255.255.255.0
[Sysname-VLAN-interface1] quit
# Create a local user named admin, and set the password to admin for the user. Specify the telnet service
type for the local user, and set the command level to 3 for this user. 
[Sysname] local-user admin
[Sysname-luser-admin] service-type telnet 
[Sysname-luser-admin] authorization-attribute level 3
[Sysname-luser-admin] password simple admin

 

That easy? YES!

 

P.S.:

Maybe you will have to activate the http service if it's not enabled by default:

[Sysname]ip http enable

 

Manfred

 

 

 

 

Occasional Visitor
Posts: 1
Registered: ‎01-16-2012
Message 3 of 8 (37,733 Views)

Re: Web Management with A5120-EI Series Switches available?

hello,

 

i have do the same thing, but i got this when i go to the http interface :

HP A5120-24G-PoE+ EI Switch with 2 Interface Slots Software Version 5.20 en ab010000 Save Help Logout User has no privilege. Are you sure to save the current configuration? HP A5120-24G-PoE+ EI Switch with 2 Interface Slots Software Version 5.20 ie 0 0 admin admin 3 

 if you have an answer, i will very happy.

 

thanks

Occasional Visitor
Posts: 1
Registered: ‎01-27-2012
Message 4 of 8 (37,606 Views)

Re: Web Management with A5120-EI Series Switches available?

use firefox

Occasional Visitor
Posts: 1
Registered: ‎02-17-2012
Message 5 of 8 (37,350 Views)

Re: Web Management with A5120-EI Series Switches available?

Security Logging Disabled
Occasional Visitor
Posts: 1
Registered: ‎03-15-2013
Message 6 of 8 (30,472 Views)

Re: Web Management with A5120-EI Series Switches available?

are there a web mangement manual?

Occasional Advisor
Posts: 7
Registered: ‎02-04-2013
Message 7 of 8 (25,959 Views)

Re: Web Management with A5120-EI Series Switches available?

I have the same problem. How can I resolve this issue? With firefox it work but most customers does only use IE

Valued Contributor
Posts: 204
Registered: ‎10-06-2013
Message 8 of 8 (20,711 Views)

Re: Web Management with A5120-EI Series Switches available?

I think the user you wish to use must have the following service-type defined:

 

service-type web

 

And make sure you have "ip http enable" in the config (if you wish to use unencrypted http webgui):

 

display current-configuration | begin http

 

The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation.