12-12-2004 08:41 AM - last edited on 06-24-2013 06:51 PM by Maiko-I
When booting the Compaq Deskpro ENS P800 for the first time, I sometimes get the following error message:
The following configuration options were automatically updated:
Disk 6448MB Fujitsu MPB3064ATU
CD Rom LTN485
If you are running UNIX, you need to configure your system using the Computer Setup Utility (F10).
F1 to save changes
I have pressed F1 and sometimes the PC continues to boot - but sometimes it comes up with the error Non-system diskette!!!
Has anyone got any ideas what the problem could be and more importantly how to rectify it? Please.........
P.S. This thread has been moved from Business PCs - Compaq, Elite, Pro to Business PCs - Evo, Deskpro, Vectra, Kayak, Brio, e-PC - HP Forum Moderator
12-12-2004 02:19 PM
12-12-2004 09:16 PM
If I change this battery, do I need the original disks - cos I don't have them - it is an ex-company pc!!!! Will changing this battery mean that settings and passwords are lost?
Why doesn't this problem occur every time and once you have managed to do the first boot - you can turn the pc off/on during the rest of the day - usually without problem!!!!
Thanks so much for taking the time to reply!!
12-12-2004 11:11 PM
Depending on how quick you are at changing the battery, CMOS may or may not get empty. Most of the time, 10 mn at least are necessary to clearing CMOS instructions completely.
No sweat however. If the pass-word is lost, the system should start without it. You'll just have to inform the BIOS with a new one as necessary.
12-13-2004 01:46 AM
Based on what you've described, I would submit another possibility. Either your hard drive or optical drive are having problems. This particularly seems likely because you intermittently do not see the hard drive. Any chance you can swap out the hard drive?
Hope this helps,
I am an HP Employee.
12-13-2004 02:19 AM
Good point but personally, I'd run Scandisk and/or audit the HDD prior to swapping anything out.
12-13-2004 08:48 AM
Well, the progress is that everyone seems to think that it is the bios battery - so I will change that in due course!!!
However, in the meantime, have bought a new laptop!!!!!!!!!!!
Will change the bios battery when laptop is all configured and working.
Am concerned about changing the bios battery but have been reassured that whilst the time settings may be lost - it should otherwise be ok. No disks needed nor passwords!!!!!
Thanks to all
12-22-2004 06:26 AM
well the latest on this pc is very strange!! I ran scandisk which took many hours with no errors found!!! The following day the PC booted up with no problems at all and for the next 3 days as well!!!!!!
Anyway, I took the decision to replace the BIOS battery - I did this quite quickly!!! The next couple of days there were no error messages but today we have the same error message back again!!!!
The following configuration options...........
........to configure your system using the Computer Setup Utility (F10).
This problem has become personal as I really would like to resolve it!!!
Unfortuntately I do not have any windows installation disks and there is no Diagnostics on the pc other than Dr Watson!!!
Any other ideas would be more than welcome.
12-22-2004 09:18 AM
This problem should have nothing to do with the operating system or the harddrive.
If the battery doesn't help (and is correctly installed - is your clock keeping good time?) and the above does not help then I fear your CMOS may be getting tired.
There are a few programs and viruses that mess with the CMOS but they are pretty rare. You can try one of the online virus scan services like panda or trend. Just in case.
You might also pop the top and verify that the ribbon cables are all nicely seated since the two devices mentioned are IDE.
Your software downloads are at:
You should be able to find a Compaq Diagnostic program for your operating system.
12-22-2004 09:29 PM
Thanks for replying. The pc already has Norton anti-virus, would that pick up any CMOS viruses???
Why is it that if the pc is on for a number of hours - then it will start for the next few days quite happily?
If the CMOS is on its way out - is it replaceable?
I am sure this problem appeared just after or shortly after I installed a scanner - is that possible???
12-23-2004 04:00 AM
ACPI IRQ Holder for PCI IRQ Steering
Error code 22
Any idea what this means? Could it be connected with the original system configuration error message somehow?
06-24-2013 08:45 AM - edited 06-24-2013 08:53 AM
Like yourself, I have the same problem and have replaced the battery. It didn't work. I get the same message saying "The following configuration options were automatically updated and the a list of CD-Roms and push F1. I have to do this twice and the second time hold this key down until the HP splash screen comes up. I have read other post that say it's a BIOS problem so I went to Hp support and installed latest one to no avail. Somebody out there has got to have a answer. Please, Would appreciate any intelligent help!
08-31-2013 04:17 PM
Sorry about not getting back to you sooner but I just today found the cure to my computer (stating the following configuration options were automatically updated) 1 go into setup, enter, or F10, 2 Go to advance settings 3 find post mode and with direction keys put it on full boot (not quick boot) I also went to Post message and enabled this (Don't know if this made any differance) 4 Go to first item and save changes and quit push F10 if promted and shut down. 5 restart computer and it will do a memory check in upper left hand conner of which you can do Esc. to stop and give you imediate memory installed and it will then go to boot. No More Pushing F1, No More Stupid Stuff about The following configuration options etc.etc.etc. AND. no more so called advisors telling you to replace you battery, or your memory, hard drive. Etc.
12-31-2013 04:55 PM
On some Deskpros as well as on some Phoenix Bios systems there is an option in the bios that resets the bios itself after reboot.
The option is called " Restore Default Settings" or "Reset Configuration Data" or "Load orginal conf during Startup".
It should be set to know and then your pc should no longer reboot with telling you should change the settings again.